GLOAPM.COMВакансії для моряків
За рангом
За типом судна
На карті
Новини та навчальні матеріали
Для моряків
Для компаній
Пошук за актуальними вакансіями:
Показати фільтри
Пошук резюме для моряків:загальна базамоя база
Головна Онлайн-тести CES Slow Speed 3rd-Eng/4rd-Eng Test for specialists working in Engine room (CES v6.0)
Онлайн-тестування: Test for specialists working in Engine room (CES v6.0)
Виберіть режим роботи з тестом:
Навчання
Онлайн-тест
Опис
Відгуки
Тест складається із 80 випадкових питань.
Усього питань на цю тему: 147
Усього питань на цю тему: 147
Питання 1 з 80
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
- 31
- 32
- 33
- 34
- 35
- 36
- 37
- 38
- 39
- 40
- 41
- 42
- 43
- 44
- 45
- 46
- 47
- 48
- 49
- 50
- 51
- 52
- 53
- 54
- 55
- 56
- 57
- 58
- 59
- 60
- 61
- 62
- 63
- 64
- 65
- 66
- 67
- 68
- 69
- 70
- 71
- 72
- 73
- 74
- 75
- 76
- 77
- 78
- 79
- 80
For two generators running in parallel, their share of additional load (kW) will be determined by the:
Voltage droop setting on each AVR.
Governor droop settings on each prime mover.
The temperature difference between the generator rotors.
The power factor of the additional load.
The exhaust gas temperatures of all cylinders of a diesel engine are seen to be high. Select, from the options given, the most likely cause of this:
Insufficient cooling of the main bearings.
Poor fuel oil quality.
High wear rate in one of the fuel injection pumps.
One of the fuel cams is worn.
What is likely to be the cause of black smoke from a diesel engine exhaust seen at the funnel?
Engine is burning some lubricating oil.
Too much combustion air.
Incomplete combustion of the fuel.
Water in the fuel.
You are starting to get low on water in the lifeboat. What should you do?
Use sea water.
Collect rain water.
Drink urine.
Mix sea water with 50 % fresh water.
PT-100 sensors are some times used with 3 or 4 wires. What is the reason for this?
Higher mechanical strength of the cable.
For fault indication.
Because of power-consumption.
Higher measuring accuracy.
With regard to radar, what would be a correct form of response to the question: “What range scale are you using?”
The correct form of response would be: “I am using the 12 mile range scale”.
The correct form of response would be: “I am using the largest range scale”.
The correct form of response would be: “I am using the 10 cm radar”.
The correct form of response would be: “I am using the 3 cm radar”.
What is the correct name of the tool shown in the illustration?
Pliers.
Adjustable wrench.
Chisel.
Open end wrench.
Which diagram is the symbol for a THYRISTOR?
Figure 3.
Figure 4.
Figure 2.
Figure 1.
What could cause diesel engine lubricating oil to appear cloudy with a slightly “milky” colour?
Fuel contamination of the system.
Oxidation of the oil.
High temperature of the oil.
Water contamination of the system.
Is it necessary to cool the samples taken from a diesel engine cooling water system before carrying out tests to determine the concentration of treatment chemicals?
No, the test should be carried out at system temperature.
Yes, the samples should be cooled to approximately 25 °C.
Yes, the samples should be cooled to approximately 50 °C.
No, the samples should be heated to approximately 95 °C.
After main power is restored (following a blackout), a timed sequential restart of motor driven auxiliaries is necessary to avoid:
Generator overload due to many motors starting at simultaneously.
Overvoltage due to current surges.
Overloading creating earth faults.
Over-frequency due to overspeed of generator.
What type of construction material should be avoided regarding fire protection purposes? (SOLAS II-2/2.2.3).
All combustible materials.
All uncovered wooden materials.
All composite materials.
All plastic materials.
What is the most important task after carrying out any major overhaul on a diesel engine?
Start the engine to check the direction of rotation.
Repair any damaged paint work on the engine.
A thorough check inside the engine to make sure all tools and cleaning rags have been removed.
Start the auxiliary blower to ventilate the engine so that it has sufficient fresh air for starting.
Which of the following fittings shall be provided to all lifeboats?
A manually controlled lamp fitted on the outside.
A remotely operated steering arrangement.
An electric power starting system for the propulsion engine with one rechargeable energy source.
Permanent boarding arrangements on both sides to enable persons in the water to board the lifeboat.
A mechanical seal, consisting of carbon and ceramic seal rings, is to be fitted to a centrifugal pump shaft. What is the most likely result of not being extremely careful when fitting this type of seal?
The seal rings are hard and may score the pump shaft.
The spring and bellows for the seal can be easily damaged.
The seal rings are brittle and can be easily chipped or damaged.
The rubber O rings for the seal can be easily damaged.
What do you understand by: Bitter end?
Bitter end means: the end link of an anchor cable that is secured within the chain locker.
Bitter end means: a foul taste at the end of a meal.
Bitter end means: to the very last moment.
Bitter end means: the toggled end of a lifeboat painter.
What is the correct name of the tool shown in the illustration?
Flat file.
Chisel.
Pliers.
Grinding machine.
What is the best method to use to remove heavy scale and fouling from the plates of a heat exchanger?
Use high-pressure cleaner with abrasive additives.
Soak the plates in recommended cleaning solution and then use a soft brush or pressure cleaner.
Use wire-brush metal scrapers and chipping guns.
Renew the plates.
What is the most important task after carrying out any major overhaul on a diesel engine?
Start the auxiliary blower to ventilate the engine so that it has sufficient fresh air for starting.
Start the engine to check the direction of rotation.
A thorough check inside the engine to make sure all tools and cleaning rags have been removed.
Repair any damaged paint work on the engine.
Many large slow speed diesel engines operating on heavy fuel oil have a fuel injection system which features Variable Injection Timing. How does this affect engine operation?
VIT increases engine efficiency by automatically maintaining the maximum cylinder pressure over the entire load range.
VIT allows the ship’s engineers to alter the injection timing for each load setting with a simple single adjustment of the fuel rack.
VIT increases engine efficiency by automatically maintaining the maximum cylinder pressure over part of the load range.
What action should be taken by the engine room rating if a piece of machinery is not functioning properly?
If machinery does not function properly, the Chief Engineer should be called out immediately.
If machinery does not function properly, it should be immediately stopped every time.
If machinery does not function properly the duty Engineer should be informed immediately so that plans for further action can be made.
If machinery does not function properly, it should be stopped and serviced immediately.
In a diesel engine lubrication system the circulating pump normally takes suction from the oil sump tank. Where would the oil normally pass to directly after the pump?
Lube oil cooler.
Main thrust bearing.
The engine bearings.
Gravity feed tank.
What would the First Engineer require?
The First Engineer would require the Chief Officer to keep him advised of bilge soundings.
The First Engineer would require the Fitter to check the carbon dioxide fire-fighting equipment.
The First Engineer would require cleaning of the feed water tank.
The First Engineer would require an inspection of the heating coils.
What do you understand by the order: “Move the pilot ladder to the other side?”
Move the pilot ladder to the other side, means: to move the pilot ladder further along nearer to the bow.
Move the pilot ladder to the other side, means: to rig another pilot ladder.
Move the pilot ladder to the other side, means: to change the position of the pilot ladder from the main deck to the fore deck.
Move the pilot ladder to the other side, means: to shift the pilot ladder to the opposite side of the ship.
During a bomb search, which of the following is an important principle to follow?
Throw any suspicious items overboard.
Try to reach behind bulkheads to find a bomb.
Do not touch any suspicious packages.
Know exactly what a bomb looks like.
What does the term “Dead Ship” mean?
“Dead Ship” means that the ship cannot make way through the water.
“Dead Ship” means that the ship is aground.
“Dead Ship” means that the machinery and boilers are inoperational due to lack of electrical power.
“Dead Ship” means that auxiliary machinery is not operational.
For a Nitrite – Borate based cooling water treatment system, what would be considered to be the normal nitrite concentration limits for a correctly dosed system?
3 000 – 4 500 ppm Nitrite.
1 500 – 3 000 ppm Nitrite.
0 – 1 500 ppm Nitrite.
4 500 – 6 000 ppm Nitrite.
During maintenance of a pneumatically operated, diaphragm actuated control valve the diaphragm is found to be split. Select, from the options given, a suitable material to use to make a temporary replacement if there is no spare diaphragm available.
Natural rubber sheet of approximately the same thickness and elasticity as the original diaphragm material.
Cotton reinforced rubber insertion sheet of smaller thickness but similar strength as the original diaphragm material.
Natural rubber sheet of greater thickness and lower elasticity as the original diaphragm material.
Cotton reinforced rubber insertion sheet of approximately the same thickness but less elasticity than the original diaphragm material.
What is the main reason for keeping engine lubricating oil viscosity within recommended limits?
To reduce system pressure losses.
To ensure the strength of the oil film is sufficient to keep lubricated surfaces apart.
It is not important.
To neutralise any acids that may form.
Modern slow speed, two stroke diesel engines often have locating pins or pegs to keep the piston rings in a fixed position. Why is this arrangement used?
The piston ring gaps can be kept in line to control the gas pressure on each of the rings.
The piston rings are more difficult to lubricate because of the slow operating speeds and will wear more quickly if they are allowed to rotate.
It avoids the risk of the ends of the piston rings being forced out by the gas pressure and catching on the scavenge ports.
It ensures the rings cannot be mixed up and that they are fitted in the correct order on the piston.
A piston rod retaining nut needs to be tightened during maintenance on the main engine. Which of the given methods should be used to ensure it does not come loose in service?
Tighten it as tight as possible using a flogging spanner and a hammer.
Tighten it 10 % more than the manufacturer’s recommendation using a torque wrench.
Tighten it to the manufacturer’s recommendations using a torque wrench.
Tighten it as tight as possible using a spanner and extension pipe.
A power card taken from a diesel engine cylinder using a mechanical indicator has a flat top. Which of the possible actions given in the options is most likely to correct this irregularity on the power card?
Lengthen the cord for the indicator drum drive.
Change the indicator spring for one with a higher rating.
Shorten the cord for the indicator drum drive.
Lubricate the indicator piston and cylinder.
A vapour compression refrigiration system is usually fitted with a number of devices to give protection and control of the system. Which of the methods given in the options should be used to test the high pressure cut out during routine maintenance and checking of the system?
Manually close each of the evaporator coils by switching off the electrical supply to the liquid line solenoid shut off valves and monitor the condenser pressure.
Close the condenser outlet valve and closely monitor the condenser pressure.
Gradually shut in the condenser cooling water valve or the condenser refrigerant inlet valve while closely monitoring the compressor discharge pressure.
Charge the system with refrigerant until the high pressure cut out operates.
What is the ideal working temperature for physical work?
-10 °C.
10-15 °C.
21-35 °C.
17-20 °C.
It is common practice to connect a resistor over an alarm contact (see diagram) in many applications. Why is this connection used?
To monitor the cable/wires for break.
To stabilise power consumption.
To avoid sparks on the contacts when opening and closing.
Enable measuring the total resistance of the circuit.
What is the correct name of the part highlighted in the illustration?
Air cooler.
Turbocharger.
Crankshaft.
Cylinder head.
Before leaving the machinery spaces of a UMS vessel after routine watchkeeping rounds in the evening, the duty engineer inspects the doors to Fuel Oil Treatment rooms which are covered by a fixed fire fighting installation. For what purpose does he do this?
To tie them open with a rope to prevent the heat from building up inside, and making it uncomfortable to work.
Remove the auto closing device so they remain in whatever position.
Wedge them open with an arrangement which allows them to be closed quickly in the event of a fire.
To make sure that they are properly closed with the self closing device so that any fire is contained and the extinguishing medium can be released without delay.
In a low pressure auxiliary boiler, what would be considered to be the maximum allowable chloride level of the boiler water?
600 PPM.
1 000 PPM.
300 PPM.
50 PPM.
During an unmanned period on a UMS vessel the “low water level” alarm for the jacket cooling water system expansion tank activates. What action would you take as duty engineer?
Answer the alarm then block the alarm and change to manned engine room condition.
Answer the alarm then block the alarm function for later action and resume unmanned operation.
Answer the alarm and adjust the alarm set point for the water level in the expansion tank before resuming unmanned operation.
Answer the alarm, top up the tank and check the system for leakage before resuming unmanned operation.
What is the correct method to use for fitting a rolling contact bearing, such as a ball bearing, onto a parallel shaft?
Use a hammer and a pipe with the same diameter as the inner bearing ring and knock the bearing onto the shaft.
Use emery cloth on the bearing surface on the shaft.
Use emery cloth on the inner ring (contact surface) of the bearing.
Gently heat the bearing in an oil bath and use a bearing puller to draw it onto the shaft.
On finding a person apparently unconscious in a High Voltage switch room, which of the following should be done?
Raise alarm then drag the victim clear so that they cannot reach live parts while receiving aid.
Check if the victim is in contact with live parts and if not apply first aid.
Raise alarm, identify means of isolation and apply before approaching victim.
Trip all breakers and approach victim.
For ideal synchronising as the incomer circuit breaker contacts make, the phase angle difference between the incomer e. m. f. and the busbar voltage should be:
90° lag.
30° ahead.
30° behind.
0°.
What is the correct name of the part highlighted in the illustration?
Crosshead.
Liner.
Bottom end bearing.
Connecting rod.
What is one of the main features of the cylinder lubricating oil used in large 2 stroke marine diesel engines which normally operate on heavy fuel oil?
It is neutral with a pH value of 7.
It is a pure mineral oil without any special additives.
It is strongly acidic.
It is strongly alkaline.
What is the main advantage of having a central cooling system fitted on board ship?
It should require less maintenance than a conventional system using only sea water.
It is a simple system with minimum control requirements.
It does not require any seawater.
Only one heat exchanger is needed for all cooling duties.
What is the meaning of “make fast”?
To act quickly.
To avoid all meals.
To secure a rope.
To coil a rope.
What are the lists called that give the position and task during a lifeboat drill for all persons on board the ship?
The Crew List.
The Muster List.
The Duty List.
The Drill List.
When a ships derrick or crane lifts a weight off the deck of a ship, from which position can the centre of gravity of the weight be considered to act?
From the centre of the weight lifted.
From the position on the deck from which the weight was lifted.
From a position on the deck at the base of the derrick or crane.
From the head of the derrick or crane.
What effect does an increased oil feed flow rate have on the performance of a centrifuge operating as a purifier?
Separating efficiency is unchanged.
Separating efficiency is increased, more water is removed.
Separating efficiency is increased, more solids are removed.
Separating efficiency is reduced.
Give the meaning of the following symbol:
Indicates manual starting direction of the engine.
Start water spray.
Reverse engine.
Start engine.
Which of the following alternatives summarise the benefits of using high voltage on ships?
Smaller conductors, machines and switchgear.
Smaller conductors, insulators and transformers.
Smaller cables and better power factors.
More efficient transformers and electrical machines.
What is generally considered as the minimum safe time period before opening a crankcase door after the oil mist detector alarm has activated and the engine has been stopped?
After at least 20 minutes.
After at least 5 minutes.
After at least 1 hour.
After at least 10 minutes.
What do you call the wide rung on a pilot ladder that prevents the ladder from twisting?
The wide rung on a pilot ladder that prevents it from twisting is called a “Spreader”.
The wide rung on a pilot ladder that prevents it from twisting is called a “Wide step”.
The wide rung on a pilot ladder that prevents it from twisting is called a “Long rung”.
The wide rung on a pilot ladder that prevents it from twisting is called a “Ani-twist rung”.
What function is this operational amplifier circuit performing?
Integrator.
Differentiator.
Non-inverting amplifier.
Inverting amplifier.
When referring to onboard oil treatments using a centrifuge, what is meant by the term purification?
Separation of solid contaminants from a liquid during the process.
Separation of two insoluble liquids with different densities, and the removal of solids in the same process.
It is a general term applied to a process for cleaning oil using a centrifuge.
Separation of one insoluble liquid from another.
Where would you find out which fire sections are enclosed by “A” or “B” class divisions on a ship?
All the mentioned alternatives.
On the general arrangement plan.
On the capacity plan.
On the Ship’s fire control plans.
Which of the following is not a principle of heat transfer utilised in an oil fired steam boiler?
Forced convection.
Conduction.
Radiation.
Natural convection.
Personnel in a high voltage switchroom and smell rotten eggs. What may this indicate?
Burning of insulation.
Arcing at badly coupled bus bars.
Problems with a vacuum circuit breaker.
Problems with a gas (SF6) circuit breaker.
An important quantity which is useful in circuit analysis is known as conductance G (Siemens). Which of the formulas A to D expresses the conductance for this circuit?
G = 1/R.
G = 2R.
G = R·V.
G = I/R.
What is the approximate content of oxygen in air?
21 %.
99 %.
51 %.
11 %.
A seawater pump requires overhaul but there are no spare wear rings for the casing and impeller. It is decided that new wear rings will be fabricated onboard using the ship’s lathe. What would be the most suitable material to use to fabricate the rings onboard?
Mild steel.
Aluminium brass.
Aluminium.
Zinc.
Before leaving the machinery spaces of a UMS vessel after routine watchkeeping rounds in the evening, the duty engineer inspects the doors to Fuel Oil Treatment rooms which are covered by a fixed fire fighting installation. For what purpose does he do this?
To tie them open with a rope to prevent the heat from building up inside, and making it uncomfortable to work.
To make sure that they are properly closed with the self closing device so that any fire is contained and the extinguishing medium can be released without delay.
Wedge them open with an arrangement which allows them to be closed quickly in the event of a fire.quickly.
B Class divisions in ships are constructed so that they are capable of preventing the passage of flame to the end of a standard fire test held for:
30 minutes.
15 minutes.
60 minutes.
45 minutes.
Why is it important to check the timing of diesel engine cylinder oil lubricators?
To ensure the piston is not covering the lubrication points and blocking the flow of cylinder lubricating oil into the cylinder.
To ensure the correct amount of cylinder lubricating oil is fed into the cylinders.
To ensure cylinder lubricating oil enters the cylinders when the piston is in the required position.
To avoid excess pressure in the cylinder lubrication system.
The correct time to synchronise is usually taken to be when the synchroscope reaches the “5 to 12” position and is rotating slowly clockwise. This to allow for:
Synchroscope error.
Generator phase difference error.
Circuit breaker operating time.
Synchroscope pointer time lag.
While alongside at a repair berth a new section of seawater pipe has been fabricated in a shoreside workshop from drawings supplied by the vessel. During fitting of the pipe by ship’s engineers it is noted that the pipe is too short leaving a gap of about 8 mm between the flange faces. What action should be taken to remedy this problem?
The pipe should be returned to the shoreside workshop for modification or to be remade to the correct dimensions.
The ships engineer’s should use extra long bolts and pull the flanges together.
The ship’s engineers should fit extra thick joints between the flanges to fill the gap.
The ship’s engineers should manufacture a spacer piece to fit the gap.
What is the correct name of the tool shown in the illustration?
Pliers.
Chisel.
Monkey wrench.
Padlock.
What do you understand by: “Let go the port anchor?”
Let go the port anchor means: slacken the port anchor cable.
Let go the port anchor means: put the port windlass brake in gear.
Let go the port anchor means: put the port windlass brake in gear and lower the anchor.
Let go the port anchor means: open the port windlass brake.
How many Radar Transponders (SART) are required to be carried onboard a ship for use in survival crafts?
One in each lifeboat.
2, one of which being capable of floating free if the ship sinks.
Two on each side of the ship.
One on each side of the ship.
Thermistors are temperature sensitive devices. A positive temperature coefficient thermistor will typically have:
Relatively linear characteristic.
Inaccurate measurement.
Relatively non linear characteristic.
Variable reliability.
Why is it important to check the timing of diesel engine cylinder oil lubricators?
To ensure the piston is not covering the lubrication points and blocking the flow of cylinder lubricating oil into the cylinder.
To ensure cylinder lubricating oil enters the cylinders when the piston is in the required position.
To ensure the correct amount of cylinder lubricating oil is fed into the cylinders.
To avoid excess pressure in the cylinder lubrication system.
The two instruments necessary for generator synchonising are:
kW meter and frequency meter.
Voltmeter and synchroscope.
Synchroscope and kVar-meter.
Amp-meter and volt-meter.
Many large slow speed diesel engines operating on heavy fuel oil have a fuel injection system which features Variable Injection Timing. How does this affect engine operation?
VIT increases engine efficiency by automatically maintaining the maximum cylinder pressure over the entire load range.
VIT increases engine efficiency by automatically maintaining the maximum cylinder pressure over part of the load range.
VIT improves engine operation by automatically controlling the start of fuel injection when it detects a poor quality fuel.
VIT allows the ship’s engineers to alter the injection timing for each load setting with a simple single adjustment of the fuel rack.
Vibration analysis is often used as a conditioning monitoring tool onboard ship as part of the approved planned maintenance system. Many vibration measuring instruments are fitted with a harmonic filter/analyser. How would these filters normally be used during vibration measurement on a centrifugal pump?
To block out any noise or vibration from the surrounding engine room.
To generate an audible sound signal at the same frequency and amplitude as the vibration.
To isolate a single frequency of vibration associated with one of the pumps components.
To sum up all the harmonics of a base frequency to give total vibration for all of the pump’s components simultaneously.
What would be the correct form of response to the question: “What kind of assistance do you require?”
The correct form of response would be: “There is a fire onboard my vessel”.
The correct form of response would be: “My vessel has a fire in the accommodation and we require fire-fighting assistance”.
The correct form of response would be: “I need help on board with a fire and the smoke is very toxic”.
The correct form of response would be: “I need help as soon as possible”.
An earth fault exists on the blue line of a 100 A bilge pump circuit. A second earth fault occurs on the yellow line of a 10 A ventilation fan circuit. Both systems are supplied from the ship’s 440 V supply. The likely outcome is that:
A short circuit occurs between earth faults and the ventilation fan fuse blows.
An open circuit occurs between earth fault and both motors trip out.
A short circuit occurs between earth fault and the bilge pump fuse blows.
Both motors trip out on overload.
What is the correct name of the part highlighted in the illustration?
Push rod.
Crankshaft.
Camshaft.
Connecting rod.
A seawater pump requires overhaul but there are no spare wear rings for the casing and impeller. It is decided that new wear rings will be fabricated onboard using the ship’s lathe. What would be the most suitable material to use to fabricate the rings onboard?
Mild steel.
Zinc.
Aluminium.
Aluminium brass.
Modern slow speed, two stroke diesel engines often have locating pins or pegs to keep the piston rings in a fixed position. Why is this arrangement used?
The piston ring gaps can be kept in line to control the gas pressure on each of the rings.
The piston rings are more difficult to lubricate because of the slow operating speeds and will wear more quickly if they are allowed to rotate.
It avoids the risk of the ends of the piston rings being forced out by the gas pressure and catching on the scavenge ports.
It ensures the rings cannot be mixed up and that they are fitted in the correct order on the piston.
What is the correct name of the part highlighted in the illustration?
Crankcase relief valve.
Push rod.
Crankshaft.
Camshaft.
The subject “Engine, Operational, Slow Speed” covers both theoretical and practical aspects of safely working with electrical equipment. Mastery of this material is a direct indicator of an employee’s competence in holding a relevant position aboard a vessel. A sailor in the engine department is responsible for maintaining and adjusting engine components, cooling systems, fuel delivery systems, and other related equipment. They are also tasked with monitoring the operation of all machinery, carrying out regular technical inspections, and performing necessary repairs. When handling a low-speed control system (SU), the sailor ensures precise and safe navigation of the vessel, following the captain’s instructions and navigational charts.
- Test type: STCW.
- Version: 6.0.0, 6.0.13.
- Department: Engine.
- Level: Operational.
- Engine: Slow speed.
Відгуки можуть залишати лише моряки. Щоб залишити відгук, зайдіть на сайт під обліковим записом моряка.
Залишіть перший відгук про цей онлайн-тест!